POA Site Supporter
Prowler Junkie

From:Burtonsville, MD
Registered: Jan 2001
Admin Use

posted 11-02-2013 08:40 AM                  

---

This was intended as an wall art project, not as a replacement trunk lid. There appears to be some prior repair/mod work on both upper corners. It is in the natural, un-prepped, un-painted form, scuff marks, but no dents. It appears to be intact otherwise - brackets, latch. hole locations. etc.

Shipping is probably oversized - 70x50x20 75 lbs. from 20866 zip code

$600 + shipping...NEW PRICE

This message has been edited by MeanGene on 12-06-2017 at 01:45 PM

POA Site Supporter
Prowler Junkie

From:scottsdale,az,usa
Registered: Jun 2001
Admin Use

posted 11-02-2013 10:57 AM                  

---

ryi-if youre not aware of it this lid has no mounting nuts in the holes for anything,no way to mount it and the nuts cannot be added later.sorry the nuts shoud be welded inside the holes.there have been a couple around lately,good for hanging on a wall.

This message has been edited by catfish on 11-02-2013 at 11:02 AM

POA Site Supporter
Prowler Junkie

From:Burtonsville, MD
Registered: Jan 2001
Admin Use

BANNED

From:Ontario, Canada
Registered: Jul 2011
Admin Use

posted 11-03-2013 03:50 PM                  

---

FYI, there are no welded nuts in the trunk lid. There is a steel plate, sandwiched in between the aluminum, and it has threaded holes in it. It is riveted in position. You could install that plate after the fact if you had one. It can slide in the opening.

It looks to me that they exist in this trunk lid as I can see the 5 rivets holding it in place.The plate itself is black so it would be hard to see in the picture.

POA Site Supporter
Prowler Junkie

From:Burtonsville, MD
Registered: Jan 2001
Admin Use

posted 11-03-2013 04:51 PM                  

---

Closer pic of the bracket

This message has been edited by MeanGene on 11-03-2013 at 04:51 PM

BANNED

From:Ontario, Canada
Registered: Jul 2011
Admin Use

POA Site Supporter
Prowler Junkie

From:Burtonsville, MD
Registered: Jan 2001
Admin Use

posted 11-03-2013 05:42 PM                  

---

The lid has ALL mounting (four) screws to mount to the hinges brackets - for any AZ wheelchair mechanic to inspect.It appears to be intact otherwise - brackets, latch. hole locations. etc.

This message has been edited by MeanGene on 11-03-2013 at 05:45 PM

BANNED

From:Ontario, Canada
Registered: Jul 2011
Admin Use

posted 11-04-2013 09:34 PM                  

---

as usual, Catfish is completely wrong.

Bump for meangene

This message has been edited by beachcat on 11-04-2013 at 09:39 PM

POA Site Supporter
Prowler Junkie

From:scottsdale,az,usa
Registered: Jun 2001
Admin Use

posted 11-07-2013 11:05 AM                  

---

the lid is supposed to have large plates with the mounting nuts welded to that plate for strength on both hinges and latch mtg area.you spoke to soon beachy.those pates are welded or riveted to the inside of the lid,plates are for added strength,otherwise eventually the nuts would rip out of thepart.

------------------

BANNED

From:Ontario, Canada
Registered: Jul 2011
Admin Use

posted 11-07-2013 05:19 PM                  

---

You are a beggar for punishment aren't you? You said the nuts were welded inside the hole. They are not. You said you were sorry but they cannot be added after. They can be.
You said they were missing from this trunk lid. They are not.

You stuck your nose in this thread with 3 wrong statemnets and now you're telling me I spoke too soon. You must have no pride whatsoever or you're just plain ,,,,,,,,,,,

POA Site Supporter
Prowler Junkie

From:Burtonsville, MD
Registered: Jan 2001
Admin Use

All times are CT (US)  Top of Page  Previous Page