Home Page | Owners Registry | Discussion Forums | ProwlerMall | Event Scrapbooks | About |
| |||||
Want to register? |
If you have previously registered, but forgotten your password, click here.
lost one of my front mud flaps including the bracket and Does any one have a spare fender bracket for sale ?? That Best regards, Kees This message has been edited by kees on 12-05-2005 at 12:36 AM When my flap and bracket came off I made a tracing of the bracket for another POA member...maybe he still has it, if that helps...... Was it the same flap that you gorilla glued?? Yep, the one I glued with the Gorilla Glue. Before installing it without the bracket still will try to get one first. Thanks. Kees Yep, the one I glued with the Gorilla Glue. Before installing it without the bracket still will try to get one first. Thanks. Kees The brackets were not available by themselves. You could make a drawing of the brackets you have left and get some machine shop to make some. They are simple brackets that a carriage bolt slips into so it would be easy to make. I have heard good things about gorilla glue but I'm not so sure it is the best to use. Others have glued theirs back on maybe someone will speak up and tell you what they have used. Brian: MUD FLAP FIXING Obtain 12 x 12” tin or heat duct flashing - Make sure the piece is thick enough so it cannot be bent in half. Cut it so it is the same shape as the recessed area on the mud flap Mark and drill the tree holes in it for the mud flap bolts –do not make the holes too big so glue does not seep through it. Slip the bolts through the holds in the flashing and epoxy them in place. Let cure for 24 hours. Buy a couple of spring clamps and SEM 39337 Non Sag Structural Adhesive Be sure to tape the back side of the mud flap so that if any glue seeps down onto the area that shows on the flap, the tape with the glue and be removed. Thoroughly clean the inside of the fender and rough it up a bit with sandpaper. Also rough us the backside of the flashing that will get the glue. Now put the SEM on the back side of the flashing, where the bolt head are, about a ¼” thick and do not go all the way to edge of the bracket as the glue will flatten out once pressed to the fender. Align on the fender and secure in place with the spring clamps and let it cure for 24 hours. Thanks for your detailed description. Highly appreciated. Best regards, Kees This message has been edited by kees on 12-07-2005 at 08:23 AM The SEM 39337 Non Sag Structural Adhesive is used primarily with fiberglass, so a shop that deals with fiberglass may have this stuff in Holland. SEM 39337 is actually two tubes of adhesive joined together. You'll need a special gun (applicator) to use with it. But a body shop may have all of this stuff. You may notice that the SEM 39337 will heat up the outside of the fender after you apply the mud flap, but it won't harm the paint. Good luck and let us know how it goes. This message has been edited by Bob Miller on 12-07-2005 at 10:03 AM kees Ladies and gents,
this time was unable to relocate it. Luckily my fender was
not damaged.
would be great !!! Perhaps someone knows a wrecked Cat or
a wrecked fender where it could be taken off.heynow14 Sounds like you need to trim them a bit. ~Robert RED5 Kees,
With the glue you really wont even need the bracket....just glue it on to the fender.kees Jesse, WildCat quote:
Originally posted by kees:
Jesse,TooHipCat quote:
Originally posted by WildCat:
The brackets were not available by themselves. You could make a drawing of the brackets you have left and get some machine shop to make some. They are simple brackets that a carriage bolt slips into so it would be easy to make.
I don't have my front tire off at the time of this post but aren't those brackets just tacked on? You're right Wildcat...just bring your drawing to any reputable machine shop and they should be able to make a couple up for you. I would definitely keep a spare on hand after this incident.
Don't forget to trim your new ones and "Loctite" the nuts when you reinstall. Good Luck!Bob Miller Here's what I did when I had the exact same issue - so far so good! Good luck. Also Sir Real used this technique with success. kees Bob,
Will see if I can manage to follow your guidelines.Bob Miller You can thank Bob Goetz at REAL ROD for most of this info as he gave it to me.
All material contained herein, Copyright 2000 - 2020