 Click here to return to the Prowler Online Board Main Page |
 ProwlerOnline, Plymouth/Chrysler Prowler Discussion Forum
 General Prowler Discussion
 Once again they are a GREAT Vendor!
|
| Bottom of Page | next newest topic | next oldest topic |
| Author | Topic: Once again they are a GREAT Vendor! |
|
Y2KRedProwler Prowler Junkie From:Los Angeles Area, CA,USA |
posted 01-11-2008 04:01 PM
    
I ordered a set of lifts from LS Technologies about three weeks ago. Howard (yes "the Howard") and I tried to install them and they wouldn't fit. Ends up, I have the 1 in 10,000 Prowlers that their standard Prowler size lifts would not work. After talking with them, they made me a special size that would fit. Received them today and they fit great! NOW THAT IS WHAT CUSTOMER SERVICE IS ALL ABOUT!! |
Simonsez                  POA Site Supporter Prowler Junkie From:Evansville, IN, US |
posted 01-11-2008 06:01 PM
David. It's time to go racing! |
Howard POA Site Supporter Prowler Junkie From:Valencia, CA, USA |
posted 01-11-2008 07:02 PM
David and I tried to put on the hood lifts with no success. I had an idea. I pulled out my welding torch, hooked up my Carbon dioxide + Argon gas tank and lit the torch. The flame was perfect. I approached the red Prowler and was just about to make some very minor adjustments to the hood brackets when I heard a scream. It was David screaming. He said stop, Steve was on the phone.
David came running into the garage and said he had a great conversation with Steve. Steve was sending him some replacement hood lifts. David was very happy. He said Steve’s customer service was outstanding. I knew this, as I had purchased hood lifts from him several months ago.
|
catfish   POA Site Supporter Prowler Junkie From:scottsdale,az,usa |
posted 01-11-2008 08:13 PM
my 99 came with the hood rods and the studs for the supports but no supports.stock ones which i purchased fit correctly.what was wrong with yours?to short or to long. ------------------ |
|
Y2KRedProwler Prowler Junkie From:Los Angeles Area, CA,USA |
posted 01-11-2008 10:18 PM
Jan - Everything in my life so far has been "too short" but in this case the LST lifts were too long. What I would suggust is next time the AZ Prowlers get together, pop off one of their OEM lifts (takes about 2 seconds) and raise your hood to the max. Attach the rod end of the OEM lift to the attachment point on the body of the prowler and see how it relates to the attachment point on the hood. My prowler would only allow for the size of the OEM lift. The OEM lift's overall length is approx. 9-9/16" long, whereas, LST lift's overall length is approx. 10-1/4" long. *IMPORTANT NOTE: DON'T LET HOWARD NEAR YOUR CAR WITH HIS WELDING EQUIPMENT!...HE IS NOT CERTIFIED FOR PROWLER MODIFICATIONS! (TRUST ME ON THIS NOTE)* PLUS I HAD TO BUY HIM A CORNED BEEF ON RYE FOR HELPING ME! BRUCE.....WE CAN GO RACING IN AUGUST WHEN I AM THERE! This message has been edited by Y2KRedProwler on 01-11-2008 at 10:21 PM |
|
Stephen Fenner Prowler Enthusiast From:Grasswood, Saskatchewan, Canada |
posted 01-11-2008 10:30 PM
Too Long - Yes! From the conversation I had with David, I came to the conclusion that the location of the Ball Studs that are on this particular vehicle, for whatever reason, are not equally the same distance apart, as all the other 10,000 or so Prowlers. I revised the design of the second set of Supports for this Prowler as per our conversation, and (as much as it made no sense at all there being a difference on his vehicle) we came up with a solution. Now, with revised dimensions of the replacements, just going by David's explanation, we managed to produce a pair of New Hood Supports for this vehicle. |
All times are CT (US) Top of Page Previous Page | Return to General Prowler Discussion next newest topic | next oldest topic |
  |
|
Contact Us | Prowler Online Homepage
All material contained herein, Copyright 2000 - 2012 ProwlerOnline.com
E-Innovations, LP
