Author
|
Topic: Rambler Plate
|
CJ Prowler Junkie Posts: 18860 From: Rochester Hills, MI USA Registered: JUL 2000
|
posted 01-31-2003 06:12 PM
Here's Bob's new plate for his "soon-to-be" 550hp Hurst SC/Rambler!
|
butchcee Prowler Junkie Posts: 7476 From: Lake Ariel, Pa. Registered: SEP 2000
|
posted 01-31-2003 06:36 PM
Great plate!
|
Mike Krehel Administrating Kat Posts: 3047 From: United States Registered: JUL 2000
|
posted 01-31-2003 06:38 PM
|
butchcee Prowler Junkie Posts: 7476 From: Lake Ariel, Pa. Registered: SEP 2000
|
posted 01-31-2003 06:44 PM
^This message has been edited by butchcee on 01-31-2003 at 06:45 PM
|
BeWare Prowler Junkie Posts: 18511 From: Acworth,GA,USA Registered: JUL 2000
|
posted 01-31-2003 07:32 PM
Very Cool
|
Marc-Colo-99 Prowler Junkie Posts: 1614 From: Aurora, Colorado Registered: JUL 2000
|
posted 01-31-2003 08:11 PM
Dang, I like those wheels!------------------
|
GPS John Prowler Junkie Posts: 617 From: Illinois Registered: AUG 2000
|
posted 01-31-2003 09:39 PM
NICE... ~very~ nice!!!
|
Dale Beaman Prowler Junkie Posts: 2699 From: Lexington, KY, USA Registered: AUG 2002
|
posted 01-31-2003 10:10 PM
CJ, Nice looking Scrambler! Is the motor AMC? If so who built it and what are the specs? My brother has a 69 AMX that he has owned since 1972 and is wanting to get a motor built. Thanks
|
dpena Administrating Kat Posts: 5359 From: San Jose Ca Santa Clara Registered: JUL 2000
|
posted 02-01-2003 01:07 AM
|
CJ Prowler Junkie Posts: 18860 From: Rochester Hills, MI USA Registered: JUL 2000
|
posted 02-01-2003 10:08 AM
Dan!!What a great picture........I'm going to try printing that off and framing it for Bob! Thanks!!!! Wish I had the talent to do that kind of thing like you do! This message has been edited by CJ on 02-01-2003 at 10:08 AM
|
RPL Prowler Junkie Posts: 3448 From: Rochester Hills, MI Registered: JUL 2000
|
posted 02-01-2003 12:43 PM
BluBYU,Using a 1970 390 AMC engine. The '70 was best, taller deck plus 1/2" head bolts versus 7/16" in '69. The block was fully machined, bored +.040" and an internal oil line was added in the cam valley to feed both ends of the block. Traco discovered that number 7 and 8 rod bearings suffered a loss of pressure above 7,000 rpm while doing development work for Penske for TransAm racing years ago. It will have all modern parts including the new Indy Cylinder Heads aluminum AMC street heads. The engine is being built by Norm Brandes of Westech Automotive in Wisconsin. His number is 262-889-4346. Norm is working with Marlan Davis, the Tech Editor for Hot Rod Magazine. The basis of the story is to take an old, over-looked engine, add modern components and make big power on pump gas in a combination that anyone could duplicate. Norm's target is 550 hp and 550 #/ft of torque. Not bad from 400 CID if he makes it. The engine goes to an engine dyno and the numbers will tell the story. Norm took this photo and others elsewhere on the site at the old AMC Proving Grounds for possible use in the article. I've been involved with Norm for a long time and he has done a number of engines for my work projects, GM and friends, some of which are POA members. I highly recommend him. I should mention that Norm is working on a number of modifications to the 3.5 V-6 Prowler engine. He has the benefit of virtually all of the development work that has been done on the engine to date and access to inside information from DC's engine plants. He is focusing on maximizing the output of the basic engine and to making it live with supercharger and or nitrous. I may be a little premature, but he will have the basic engine combination to use for Prowler projects. This message has been edited by RPL on 02-01-2003 at 12:58 PM
|
RPL Prowler Junkie Posts: 3448 From: Rochester Hills, MI Registered: JUL 2000
|
posted 02-01-2003 12:59 PM
Dan, Thanks for the art work! I love it!
|
Todd Cameron unregistered Posts: 3448 From: Rochester Hills, MI Registered: JUL 2000
|
posted 02-01-2003 02:46 PM
Nice!
|
Marty Usher Prowler Junkie Posts: 13833 From: San Antonio, Texas Registered: JUN 2001
|
posted 02-01-2003 07:08 PM
I like the plate! I hope you hit the projected numbers on the dyno (soon )Marty
|
Randy Cobb Prowler Junkie Posts: 4070 From: Greensboro, NC Registered: JUL 2002
|
posted 02-01-2003 07:37 PM
Graet ride!------------------
|
dpena Administrating Kat Posts: 5359 From: San Jose Ca Santa Clara Registered: JUL 2000
|
posted 02-02-2003 07:25 PM
Hey Bob!!Glad you liked it!! Thank you for all the support!!
|
Marc-Colo-99 Prowler Junkie Posts: 1614 From: Aurora, Colorado Registered: JUL 2000
|
posted 02-02-2003 08:22 PM
Hey Bob & Dan I want one of the first autographed posters!
|
jd2ksilver Prowler Junkie Posts: 4360 From: Mt. View, CA Registered: JUL 2000
|
posted 02-02-2003 10:32 PM
That actually is a life size, fold up poster of himself that Dan carries around with him. Ever since he was Elvis at the Woodward Dream Cruise Dance Party he takes it everywhere,,lol ------------------ This message has been edited by jd2ksilver on 02-02-2003 at 10:34 PM
|
CJ Prowler Junkie Posts: 18860 From: Rochester Hills, MI USA Registered: JUL 2000
|
posted 02-02-2003 11:05 PM
He never has gotten over that, has he? lol!
|