Archive: Upright Trailer Stand Purchasers Please Read - ProwlerOnline, Plymouth/Chrysler Prowler Discussion Forum

Note: This is an archived topic. It is read-only.

ProwlerOnline, Plymouth/Chrysler Prowler Discussion Forum

Off Topic

Upright Trailer Stand Purchasers Please Read (Page 2)

UBBFriend: Email This Page to Someone!

profile | register | preferences | faq | search

This topic is 2 pages long: 1 2
This topic was originally posted in this forum: Tires, Rims Discusssion

Author	Topic: Upright Trailer Stand Purchasers Please Read
PANTHER CITY PROWLER Prowler Junkie Posts: 31 From: Ft Worth, Tx Registered: MAR 2002	posted 03-22-2002 09:18 PM quote: Originally posted by Larry Lord: Storing things inside the trailer when upright really isn't a problem at all. It's very easy to just place or stack the items to the rear of the trailer near the latch, place a blanket on top of the items to protect the underside of the lid if needed and then just stand the trailer up. This actually helps to decrease the tongue weight of the trailer. I too carry an E-Z Up at times along with chairs and other items. I've never had any kind of damage whatsoever. The only caution that I would give is to not store any liquids in your trailer while in storage. LARRY I'VE JUST BOUGHT A CHAMPION LUGGAGE TRAILER THAT UTILIZES THE SAME AXLE AS THE PROWLER TRAILER. GOT THE FRAME PUT TOGETHER TODAY AND WILL MOUNT THE BODY TOMARROW-ITS FIBERGLASS MULLINS STYLE. PLAN ON PUTTING PROWLER REAR BUMPER THAT I'VE LOCATED ON THE REAR. IF I DO THAT IT WILL MAYBE LONGER THAN THE STANDARD PROWLER TRAILER. PLAN TO GET WITH DAVID N. TOMARROW TO SEE IF STANDARD STANDS WILL WORK, BUT DO YOU THINK DESIGN WILL LEND ITS SELF TO LENGTHENING IF NECESSARY? ALSO THE PICTURES POSTED SHOW WHEELS IN THE BACKGROUND. DO YOU ALSO MANUFACTURE WHEELS IN ADDITION TO TOOL BOXES? THANKS ------------------ PANTHER CITY PROWLER
Larry Lord Prowler Junkie Posts: 3709 From: Colton, CA Registered: JUL 2000	posted 03-22-2002 09:25 PM There should be no problem in lengthening the rollback tubes to accomodate a longer trailer. This will however increase the amount of effort needed to lift the trailer upright. I'm not sure what the Mullin's style Champion trailer weighs. Make sure that the brackets will rest against the frame and the axle when installed. This is not a must but it will add to the stabilty of the trailer. Worst case, you may have to drill a new hole for the 1/2" bolt that bolts to the axle flange. Make a test with David's stand and let me know what you need. Sorry, I don't make wheels anymore but that's where I got my start in fabricating. Remember when "White Spoke" wheels were the rage in the late 60"s and early 70's? This message has been edited by Larry Lord on 03-22-2002 at 09:29 PM
Paul Prowler Junkie Posts: 807 From: Cedarburg, WI USA Registered: JUL 2000	posted 03-22-2002 11:17 PM Just one last comment about casters and alternatives. Yes, while PVC tubing would allow the trailer to be moved it would be primarily in a straight line once you overcome the weight of the trailer on the bar. It's a cheap alternative, yes, but does only a small part of the finesse, not the whole job casters could do. Regarding casters or ball bearing wheels, Larry, they do make them with locks that will stop the wheels from turning. You would not have to chase the trailer nor use 2 people when putting upright if, at least, the initial pair to touch the floor were locked. Or, less expensive still, chock them as you tilt up. ------------------
Larry Lord Prowler Junkie Posts: 3709 From: Colton, CA Registered: JUL 2000	posted 03-24-2002 03:09 PM Paul, I like your ideas about the casters and I'm aware of the locking style casters. As I stated before there are numerous reasons that I elected not to use casters. Following are some of my concerns with casters; 1. Added cost for an item that most users do not need 2. the over-centerline balance point changes when the wheels swivel. 3. additional height requirements needed for the casters 4. tip-stop difficulties caused by using casters 5. one person setup and ease of use 6. easy and flat storage of the tubes inside the trailer when not in use If you buy a stand and adapt your caster ideas to it, I would love to see some pictures. Maybe you can overcome some of the difficulties that I see in using casters.
Larry Lord Prowler Junkie Posts: 3709 From: Colton, CA Registered: JUL 2000	posted 03-26-2002 12:57 AM Has anyone other than fixumm had any problems with the plastic end caps? If so, is this something that you feel is important?

This topic is 2 pages long: 1 2 All times are CT (US)	This is an ARCHIVED topic. You may not reply to it!

	Hop to:

Contact Us | Prowler Online Homepage

All material contained herein, Copyright 2000 - 2012 ProwlerOnline.com
E-Innovations, LP

POA Terms of Service