Posts: 3709
From: Colton, CA
Registered: JUL 2000

posted 05-24-2004 10:39 PM         

---

Two years and 30 days after I started this project, I finished it tonight. The inspiration was from a sculpture that I had seen by DeBusk and a couple people on the POA had purchased. Since my car has no bumpers and has Carlini turn signal fairings, I needed to make my own version of his original design.
The top two pictures are before I added the turn signal bulbs and painted it but it will give you the general idea. I'll post another picture when I put it on the wall.

The third picture is the original by DeBusk.

------------------
Larry (Cruise Control) Lord
Larry@FMBbox.com
Products for your Prowler and Trailer:
Upright Trailer Storage Stands - Trailer Latch Reinforcement Kits - KatRack Stowable Cargo Carriers - Deck Lid Hinge Protectors - Pro-Strap Velcro Tie Straps - Keyed Alike Chrome Locksets - Logo Caps - Chrome Receiver Locks - Chrome Coupler Locks
FMB Prowler Products.

This message has been edited by Larry Lord on 05-24-2004 at 10:57 PM

Posts: 5068
From: Dallas, TX
Registered: OCT 2012

Posts: 5068
From: Dallas, TX
Registered: OCT 2012

Posts: 3709
From: Colton, CA
Registered: JUL 2000

posted 05-24-2004 11:11 PM         

---

No Ray, I didn't buy one.
I think Phil Genet owns the one in the picture that I posted. I'm pretty sure Blue Tie owns one also. I posted the picture so that others could see his original design and give credit where it was due.

This message has been edited by Larry Lord on 05-24-2004 at 11:15 PM

Posts: 4011
From: Toronto, Canada
Registered: SEP 2000

Posts: 13833
From: San Antonio, Texas
Registered: JUN 2001

Posts: 884
From: Marble Falls, Texas
Registered: JUN 2001

posted 05-24-2004 11:44 PM         

---

Larry, 2 cool.

This thumbs up is from Dawn.

Posts: 7907
From: Las Cruces, NM, USA
Registered: DEC 2001

posted 05-25-2004 01:02 AM         

---

Very, very ,nice.

------------------

Current mods: Mopar dual exhaust & front mudflaps; MacMotorsports Air Intake;
Real Rod Air Patrol; Graphics by Balistek Designs; ($8) Chrome grille; Chrome
tire valve-stem covers; Painted rear bumper lettering; Prowler Pro Gears; Synthetic
Oil; Raybestos Ceramic Brake Pads; TGF Door Panel Inserts & Headrest Covers;
SheepskinExpress Sheepskin Seatcovers; Grille Light; Pinstriping by Bo Boring;
Painted Valve Cover; Window Tinting; Windshield Visor Banner; Front Bumper
Removal / Relocation of Front Turn Signal Lights; Real Rod Transmission Cooler
Cover, Sill and Carper Covers, Aero Front Covers and Roadster Rear Pan, rear
bumpers removed; rear mudflaps; painted calipers; Prowler Products by Gary
Drilled Rotors, front and rear; Painted tach; Jay's Aluminum Billet Center Caps
w/shimmers, Chrome Lugnuts and Chrome Radio Bezel Shimmer; Dash Rings;
Windshield Wiper Arm Removal; Fender Trim; Speaker Replacement; Painted
Plenum; Painted Radiator Crossmember; Painted Rear Mudflaps; Air Patrol
graphics.

More 'Pumpkin' photos . . . . . More cars and other stuff

New pictures in Personal Scrapbook (02/23/03)

"I may have to grow older, but I do not have to grow up!"

"The Prowler is not a car to go from Point A to Point B. The Prowler is the Point!"

Posts: 12017
From: San Diego Area
Registered: JUL 2000

Posts: 1459
From: Marco Island Fl
Registered: NOV 2001

Posts: 4576
From: Alexandria, Virginian USA
Registered: OCT 2003

posted 05-25-2004 07:13 AM         

---

Veeery Cool...must have been a labor of love!

By the way Larry...with all your free time, how come it took two years?

Posts: 471
From: Zellwood, FL
Registered: JAN 2003

Posts: 227
From: Richmond, IN
Registered: JUL 2000

posted 05-25-2004 08:15 AM         

---

I have the DeBusk #2 / 100.

------------------
PG PRWLR
99 Red

Posts: 2388
From: SUGAR LAND, TX. USA
Registered: DEC 2003

Posts: 18860
From: Rochester Hills, MI USA
Registered: JUL 2000

Posts: 7476
From: Lake Ariel, Pa.
Registered: SEP 2000

Posts: 3709
From: Colton, CA
Registered: JUL 2000

posted 05-25-2004 09:37 AM         

---

Thanks for the compliments gang.

Butchee, It's solid. Consisiting of 1/8, 3/16 and 1/4 cold roll steel rods.

Bob, I started it and then lost interest because it was too much work. After recently remodeling my house to a modern style, I felt it would fit the decor and that I needed to just make the time to finish it. I think this will #1 of one.

Posts: 3709
From: Colton, CA
Registered: JUL 2000

Posts: 10955
From: Dallas, TX
Registered: NOV 2000

Posts: 4079
From: TORONTO,ONTARIO,CANADA
Registered: JUL 2002

posted 05-25-2004 10:33 AM         

---

I don't think anyone has mentioned this yet...but it's really cool!

------------------

Posts: 33595
From: Cincinnati, OH
Registered: JUL 2000

Posts: 7476
From: Lake Ariel, Pa.
Registered: SEP 2000

Posts: 18511
From: Acworth,GA,USA
Registered: JUL 2000

Posts: 14
From: Riverside, Ca
Registered: JUN 2003

Posts: 3915
From: Sherman CT USA
Registered: NOV 2002

posted 05-27-2004 12:06 AM         

---

I like it!!It would go great in my place! (Very Contemporary)Put me on the list when your ready to make some more!!

------------------

All times are CT (US)