Note: This is an archived topic. It is read-only.
  ProwlerOnline, Plymouth/Chrysler Prowler Discussion Forum
  Off Topic
  octane boost home brew anoy one know about this?? (Page 2)

UBBFriend: Email This Page to Someone!

profile | register | preferences | faq | search


This topic is 2 pages long:   1  2 
This topic was originally posted in this forum: Tires, Rims Discusssion
Author Topic:   octane boost home brew anoy one know about this??
firegabe
Prowler Junkie

Posts: 313
From: Ca.
Registered: NOV 2003

posted 04-15-2005 02:36 PM     Click Here to See the Profile for firegabe     
I just found this info. I thought some might be interested in it. I would certainly do more research before attempting any of the mixtures. (This info was cut and pasted from another website)


Formula #1 - Toluene
R+M/2.........114
Cost...........$2.50/gal
Mixtures with 92 Octane Premium
10%...........94.2 Octane
20%...........96.4 Octane
30%...........98.6 Octane
Notes: Common ingredient in Octane Boosters in a can. 12-16 ounces will only raise octane 2-3 *points*, i.e. from 92 to 92.3. Often costs $3-5 for 12-16 ounces, when it can be purchased for less than $3/gal at chemical supply houses or paint stores.

Formula #2 - Xylene
R+M/2.........117
Cost...........$2.75/gal
Mixtures with 92 Octane Premium
10%...........94.5 Octane
20%...........97.0 Octane
30%...........99.5 Octane
Notes: Similar to Toluene. 12-16 ounces will only raise octane 2-3 *points*, i.e. from 92 to 92.3. Usually mixed with Toluene and advertised as *race formula*.

Formula #3 - Methyl-tertiary-butyl-ether (MTBE)
R+M/2.........118
Cost...........$3.50/gal
Mixtures with 92 Octane Premium
10%...........94.6 Octane
20%...........97.2 Octane
30%...........99.8 Octane
Notes: Oxygenate. Very common in octane booster products. Has lower BTU content than toluene or xylene, but oxygenate effect makes the gasoline burn better and produce more energy.

Formula #4 - Methanol or Ethanol
R+M/2.........101
Cost...........$0.60 - $1.75/gal
Mixtures with 92 Octane Premium
10%...........94.3 Octane (Methanol)
10%...........94.7 Octane (Ethanol)
20%...........Not Recommended
Notes: Methanol is wood alcohol. Ethanol is grain alcohol and found in Gasohol in 10% ratios. Both alcohols are mildly corrosive and will eat gas tank linings, rubber and aluminum if used in excessive ratios. Main ingredient in "Gas Dryers", combine with water.

Formula #5 - Isopropyl Alcohol and Tertiary Butyl Alcohol
R+M/2.........101
Cost...........$0.60-$1.50/gal
Mixtures with 92 Octane Premium
10%...........94.5 Octane
20%...........Not Recommended
30%...........Not Recommended

Notes: Similar to Methanol/Ethanol. Isopropyl Alcohol is simply rubbing alcohol.

Sample Mixture
To make your own octane booster, it is easiest to make up a large batch, and then bottle it up in "dosage-size" uses.
Below is the basic formula of one of the popular octane booster products. To make eight 16 ounce bottles (128 oz = 1 gal):

100 oz of toluene for octane boost
25 oz of mineral spirits (cleaning agent)
3 oz of transmission fluid (lubricating agent)
This product is advertised as "octane booster with cleaning agent *and* lubricating agent!". Diesel fuel or kerosene can be substituted for mineral spirits and light turbine oil can be substituted for transmission fluid. Color can be added with petroleum dyes.

firegabe

quincy
Prowler Junkie

Posts: 1635
From: Utica, Michigan, USA
Registered: MAY 2004

posted 04-15-2005 05:24 PM     Click Here to See the Profile for quincy     
Hi Everyone,
Please be very cautious with these home brew mixes. I'm not a chemical engineer, but I know for a fact that MTBE is a nasty poison. Don't breath vapors or get on bare skin if you play. If you feed these concoctions in your stock Prowler engine, I don't think you will realize any performance gains, and may burn a valve, or worse in the process. I also remember one mix circa 40 years ago. Mix rubbing alcohol with moth balls. The Naptha and alcohol was suppose to make a poor mans nitro-methane fuel additive. Even back then I was wise enough not to tempt fate playing chemist. Good Luck!


MDProwler
Prowler Junkie

Posts: 5250
From: Fallston,MD USA
Registered: JUL 2003

posted 04-15-2005 06:32 PM     Click Here to See the Profile for MDProwler     
They are trying to outlaw MTBE in Maryland. It is already showing up in the drinking water 5 miles from where I live. Exxon is once again the center of attention.


Lone Ranger
Prowler Junkie

Posts: 2120
From: Sedalia Mo USA
Registered: MAY 2003

posted 04-15-2005 06:42 PM     Click Here to See the Profile for Lone Ranger     

I agree with quincy. This isn't like making beer in the bathtub, these are dangerous components and best to be left alone.



Randy Cobb
Prowler Junkie

Posts: 4070
From: Greensboro, NC
Registered: JUL 2002

posted 04-18-2005 07:14 AM     Click Here to See the Profile for Randy Cobb     
I agree with all posts above.

Even though some of these chemicals are typically blended in gasoline in SMALL amounts at refineries or terminals, they have properties that can be extremely hazardous if not mixed correctly in proper amounts. Even in the hands of highly trained professionals there have been horror stories.

This topic is 2 pages long:   1  2 

All times are CT (US)

This is an ARCHIVED topic. You may not reply to it!
Hop to:

Contact Us | Prowler Online Homepage

All material contained herein, Copyright 2000 - 2012 ProwlerOnline.com
E-Innovations, LP

POA Terms of Service

Powered by Infopop www.infopop.com © 2000
Ultimate Bulletin Board 5.45c