posted 02-04-2015 04:01 PM                  

Dick now has 10 sets of spinners ready to go.
The price of $450 includes drilling the center cap, replacing the tabs and retaining ring, 4 spinners, 4 decals, 4 towers, 4 spacer disks and return postage.
If you already had the repair done on your center caps, the price is $ 375.
You need to send your center caps to Dick at your cost.

The spinners will NOT fit the trailer at this point. The threads on the trailer are different than both the front and rear threads on the car itself.

posted 02-04-2015 04:06 PM                  

The towers are not round, so they can tightened with a standard wrench.

posted 02-04-2015 04:40 PM                  

quote:

---

Originally posted by ed monahan:

Dick now has 10 sets of spinners ready to go.
The price of $450 includes drilling the center cap, replacing the tabs and retaining ring, 4 spinners, 4 decals, 4 towers, 4 spacer disks and return postage.
If you already had the repair done on your center caps, the price is $ 375.
You need to send your center caps to Dick at your cost.

The spinners will NOT fit the trailer at this point. The threads on the trailer are different than both the front and rear threads on the car itself.

---

posted 02-04-2015 06:28 PM                  

quote:

---

Originally posted by ed monahan:

Dick now has 10 sets of spinners ready to go.
The price of $450 includes drilling the center cap, replacing the tabs and retaining ring, 4 spinners, 4 decals, 4 towers, 4 spacer disks and return postage.
If you already had the repair done on your center caps, the price is $ 375.
You need to send your center caps to Dick at your cost.

The spinners will NOT fit the trailer at this point. The threads on the trailer are different than both the front and rear threads on the car itself.

---

posted 02-04-2015 09:21 PM                  

Need4Speed, I THINK they must be chrome plated aluminum. They are NOT flimsy, thin aluminum. There is some heft to them but a magnet will not stick to them.

ZProwler2000, Yes you can buy just the spinners and towers. I will get a price for that.

Three of the ten sets were already sold. Two to locals who saw them at the After Christmas party and one set to First Prowler who pushed Dick to make them.

The second last picture is my car, with my tower and disk installed. That is the reason for the rust on the threads, that is NOT the new one. I had started to re-assemble my spinner but had forgotten to take a picture. Yours will not have the printing on it that says FRONT. They will only fit on the front OR the rear, you can't possibly use the wrong one.

posted 02-09-2015 01:41 PM                  

quote:

---

Originally posted by ed monahan:

Dick now has 10 sets of spinners ready to go.
The price of $450 includes drilling the center cap, replacing the tabs and retaining ring, 4 spinners, 4 decals, 4 towers, 4 spacer disks and return postage.
If you already had the repair done on your center caps, the price is $ 375.
You need to send your center caps to Dick at your cost.

The spinners will NOT fit the trailer at this point. The threads on the trailer are different than both the front and rear threads on the car itself.

---

posted 02-14-2015 03:05 PM                  

quote:

---

Originally posted by DrillinU:
Can these spinners be used with out the caps?

---

posted 02-14-2015 03:53 PM                  

I think there are only 2 or 3 sets left, by the way. Dick has let me know when folks order them but I haven't really been keeping up with it the past few days.

posted 02-14-2015 07:54 PM                  

quote:

---

Originally posted by ed monahan:
I will post a pic of the spinner WITHOUT the center cap in a day or two.
My hubs have rust on them so they look horrible. Yours might look better or I could clean mine up a bit.

I think there are only 2 or 3 sets left, by the way. Dick has let me know when folks order them but I haven't really been keeping up with it the past few days.

Michael you are quite welcome.

Originally posted by ZPROWLER2000:
[B] YES BUT YOU WILL SEE YOUR LUG NUTS,MIGHT LOOK GOOD WITH CHROME NUTS

---

posted 02-15-2015 01:43 PM                  

quote:

---

Originally posted by DrillinU:
Called Richard, picked up a set,
Jeff, I think you are right should look good with chrome Nuts

---

posted 02-15-2015 03:54 PM                  

quote:

---

Originally posted by ZPROWLER2000:

---

posted 02-15-2015 05:59 PM                  

quote:

---

Originally posted by ZPROWLER2000:

---

posted 02-16-2015 03:20 PM                  

Dick is going to make 8 more sets, but is keeping one for himself and one set is already sold.
Therefore there are 6 sets about to be ready. Late this week or early next week.
This could well be the end of them. I really don't know.
Let Dick know if you are interested in reserving a set.
If you prefer paying with Paypal, you will have to pay me and I will get the money to him. He doesn't have Paypal and doesn't do much "internetting".

posted 02-25-2015 03:28 PM                  

Dick is going to make 8 more sets, but is keeping one for himself and one set is already sold.
Therefore there are 6 sets about to be ready. Late this week or early next week.
This could well be the end of them. I really don't know.
Let Dick know if you are interested in reserving a set.
If you prefer paying with Paypal, you will have to pay me and I will get the money to him. He doesn't have Paypal and doesn't do much "internetting".

This message has been edited by ed monahan on 02-25-2015 at 12:44 AM